View B3104UCLXX_4784832.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

sidactor ? protection thyristors 122 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection battrax ? single port positive/negative - ms-013 (t) 1 (-v ref ) 2 (r) 3 6 (ground) 4 (ground) 5 (+v ref ) electrical characteristics description features and bene?ts t low voltage overshoot t low on-state voltage t does not degrade with use t fails short circuit when surged in excess of ratings t low capacitance t positive and negative ringing compatible t single-port protect t gate trgger tracking device agency approvals agency agency file number e133083 schematic symbol pinout designation 1 2 3 6 5 4 part number marking v drm @l drm = 5 a v s @100v/s i h i s i t v t @i t =2.2 amps capacitance* v min v max ma min ma max a max v max pf min pf max B3104UCLXX b3104uc iv ref **?7* iv ref **?7* 100 100 2.2 4 30 200 b3164uclxx b3164uc iv ref **?7* iv ref **?7* 160 100 2.2 4 30 200 b3204uclxx b3204uc iv ref **?7* iv ref **?7* 200 100 2.2 4 30 200 applicable global standards t tia-968-a t tia-968-b t itu k.20/21 enhanced level t itu k.20/21 basic level t gr 1089 inter-building t gr 1089 intra-building t iec 61000-4-5 t yd/t 1082 t yd/t 993 t yd/t 950 the single port positive/negative battrax series are programmable sidactor ? devices designed to protect slics (subscriber line interface circuit) from damaging overvoltage transients. this series is designed speci?cally to protect slic devices utilizing positive and negative ringing signals. this one device will protect a single port. notes: - absolute maximum ratings measured at t a = 25oc (unless otherwise noted). - devices are bi-directional - all electrical characteristics shown are de?ned from tip (pin 1) to ground (pin 4 & 6) and ring (pin 3) to ground (pin 4 & 6) - v ref max value for the negative battrax is -200 v. - v ref .by7bmvfgpsuifqptjujwf#buusbyjt7 - xx = part number suf?x: tp (tube pack) or rp (reel pack). * off-state capacitance (c o ) is measured across pins 1 & 4,6 and 3 & 4,6 at 1 mhz with a 2v bias.
sidactor ? protection thyristors 123 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection surge ratings series i pp i tsm 5 0/60 hz di/dt 0.2x310 1 0. 5 x700 2 2x10 1 2x10 2 8x20 1 1.2x 5 0 2 10x160 1 10x160 2 10x 5 60 1 10x 5 60 2 5 x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5 x310 1 10x700 2 a min a min a min a min a min a min a min a min a min a min a/s max c 50 500 400 200 150 200 175 100 200 50 500 package symbol parameter value unit modi?ed ms-013 1 2 3 6 5 4 t j operating junction temperature range up c t s storage temperature range up c r 0 ja thermal resistance: junction to ambient 60 c/w thermal considerations i h i t i s i s i drm v t +v -v +i -i v s i h v drm v ref -v ref v drm v s i pp i pp i drm 50 100 0 t r t d 0 peak value half value t C time (s) i pp C peak pulse current C %i pp t r = rise time to peak value t d = decay time to half value waveform = t r x t d v-i characteristics t r x t d pulse waveform 25c case temperature (t c ) - oc 2.0 1. 8 1. 6 1. 4 1. 2 1. 0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 ratio of i h i h (t c = 25oc) normalized v s change vs. junction temperature normalized dc holding current vs. case temperature -8 -40 -20 0 20 40 60 80 100 120 140 160 -6 -4 0 2 4 6 8 10 12 14 junction temperature (t j ) C c percent of v s change C % 25 c notes: 1 current wavef orm in s 2 voltage wavef orm in s - peak pulse current rating (i pp ) is repetitive and guaranteed for the life of the product. - i pp sbujohtbqqmjdbcmfpwfsufnqfsbuvsfsbohfpg?$up?$ * pp rating assumes v ref frvbmt7
- the device must initially be in thermal equilibrium with -40c < t j < ?$
sidactor ? protection thyristors 124 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection time temper at ure t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature (t 25oc to peak) ramp-down ramp-up preheat critical zone t l to t p figure 1 soldering parameters physical speci?cations environmental speci?cations lead material copper alloy terminal finish 100% matte-tin plated body material ul recognized epoxy meeting ?ammability classi?cation 94v-0 part numbering part marking high temp voltage blocking 80% rated v drm (v dc peak
?$ps?$ 504 or 1008 hrs. mil-std-750 (method 1040) jedec, jesd22-a-101 temp cycling ?$up?$ njoexfmm vqup cycles. mil-std-750 (method 1051) eia/jedec, jesd22-a104 biased temp & humidity 52 v dc ?$
3) vqupist&*" jedec, jesd22-a-101 high temp storage ?$ist.*-45% .fuipe
jedec, jesd22-a-101 low temp storage -65c, 1008 hrs. thermal shock ?$up?$ njoexfmm tfdusbotgfs 10 cycles. mil-std-750 (method 1056) jedec, jesd22-a-106 autoclave (pressure cooker test) ?$ 3) bun vqupist&*" jedec, jesd22-a-102 resistance to solder heat ?$ tfdt.*-45% .fuipe
moisture sensitivity level 3) ?$ ist sfnpxdzdmft ?$1fbl
+&%&$+45% -fwfm re?ow condition pb-free assembly (see fig. 1) pre heat - temperature min (t s(min) ) ?$ - temperature max (t s(max) ) ?$ - time (min to max) (t s ) 60-180 secs. average ramp up rate (liquidus temp (t l ) to peak) 3c/sec. max. t s(max) to t l - ramp-up rate 3c/sec. max. re?ow - temperature (t l ) (liquidus) ?$ - temperature (t l ) 60-150 secs. peak temp (t p )
?$ time within 5 c of actual peak temp (t p ) 30 secs. max. ramp-down rate 6c/sec. max. time 2 5 c to peak temp (t p ) 8 min. max. do not exceed ?$ xxxxxxx xxxxx part marking code (refer to electrical characteristics table) date code b3 xx 4 u c l xx type holding current package type i pp rating rohs compliant construction variable packing options rp: reel pack tp: tube pack b3: dual (positive & negative battrax sidactor) 10: 100 ma 16: 160 ma 20: 200 ma
sidactor ? protection thyristors 12 5 revised: february 22, 2011 ? 2011 littelfuse, inc. speci?cations are subject to change without notice. please refer to www.littelfuse.com for current information. slic protection package type description quantity added suf?x industry standard u modi?ed ms-013 6-pin tape and reel pack 1500 rp eia-481-d modi?ed ms-013 6-pin tube pack 500 (50 per tube) tp n/a packing options tape and reel speci?cation ms-013 interior of the tube .045 (1.14) .165 (4.19) .150 (3.81) 90? .525 (13.34) a .225 (5.72) message location .310 (7.87) .108 (2.74) .005 20.000 .030 (508.00 0.76) .020 .005 (0.51 0.13) wall typ. .110 (2.79) a 6 dimensions are in inches (and millimeters) direction of feed 0.700 (17.8) .512 (13.0) arbor hole dia. 12.99 (330) .630 (16.0) dimensions are in inches (and millimeters) .472 (12.0) .157 (4.0) tube pack speci?cation ms-013 dimensions ms-013 7o typ e d a b mold split line a 7o typ 7o typ pad outline 0.065 (1.65) 0. 4 60 (11.68) 0.138 (3.50) 0.059 (1.50) c a f 7o typ g j h dimension are in inches (and millimeters). burr side min length of flat 4 o 96o detail a k bsc* dimensions inches millimeters min max min max a 0.360 0.364 9.14 9.25 b 0.352 0.356 8.94 9.04 c 0.400 0.412 10.16 10.46 d 0.043 0.045 1.09 1.13 e 0.047 0.055 1.19 1.40 f 0.293 0.297 7.44 7.54 g 0.289 0.293 7.34 7.44 h 0.089 0.093 2.26 2.36 j 0.041 0.049 1.04 1.24 k 0.020 0.51 bsc* 0.133 0.143 3.38 3.63 * bsc = b asic s pacing between c enters

▲Up To Search▲

Price & Availability of B3104UCLXX

	To Download B3104UCLXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .